Frequently Asked Questions

HomeGuide's national range for installed epoxy is $4 to $10 per square foot, or about $1,600 to $5,800 for a two-car garage. Polyaspartic runs about $5 to $12 per square foot. Removing an old coating, repairing cracks and adding flake or metallic finishes raise the total, so we price each floor after seeing it.

At HomeGuide's $4 to $10 per square foot, a 500 square foot floor works out to roughly $2,000 to $5,000 for epoxy. HomeGuide's polyaspartic table puts 500 square feet at $2,500 to $6,000. Heavy prep, such as grinding off paint or patching many cracks, can push a floor above those numbers.

Epoxy needs a dry, well-prepared slab and can peel if moisture or oil is trapped under it. HomeGuide notes standard epoxy can take up to a week to fully cure and rates its UV resistance as poor to fair, so in Florida sun it can yellow without a protective topcoat. A glossy finish can also be slippery when wet unless texture or flake is added. Each of these is handled with the right system and prep.

Floors are coated with water-based, solvent-based or 100% solids epoxy. HomeGuide lists water-based epoxy as lasting about 3 to 5 years and solid epoxy about 10 to 20 years. Professional garage and commercial floors normally use 100% solids epoxy under a polyaspartic or urethane topcoat. Most store kits are thinner water-based products.

Standard epoxy can yellow where sunlight reaches it, usually first in the strip of floor inside the garage door. We prevent that with a UV-stable polyaspartic topcoat, which HomeGuide rates as excellent for UV resistance. On lanais and pool decks we use UV-stable outdoor systems from the start.

Yes, with care. We measure humidity, air temperature and dew point before each coat, often start early in the morning, and keep the garage closed while the coating sets. If the conditions would trap moisture in the coating, we reschedule.

Inside a private garage you often do not, but many condo associations and some HOAs require approval for work in shared garages, on lanais or on anything visible from outside. Check your association's rules before the install date. We can give you a written description of the system and colors to submit.

HomeGuide's national range for a two-car garage is about $1,600 to $5,800 for epoxy and $2,000 to $6,900 for polyaspartic. Removing paint or an old coating, repairing cracks and choosing a full flake finish move the price. We give you a written number after measuring and testing the floor.

HomeGuide says polyaspartic is ready for heavy vehicle traffic in about 24 to 48 hours and that standard epoxy can take up to a week to fully cure. The exact time depends on the system, temperature and humidity on install day. We give you a specific time for your floor.

A smooth, glossy coating can be slick when rain blows in or you come home wet from the beach. Flake floors have built-in texture, and we can add an anti-slip aggregate to the topcoat on solid-color floors.

Usually the prep. Kits rely on acid etching, which does not remove old sealer, oil or weak surface concrete, and many are thin water-based products. Hot tires then lift the coating. A diamond-ground floor and a thicker system with a hard topcoat bond far better.

For most garages, yes. A full flake floor hides sand, dust and water spots, adds texture for grip and is more forgiving of small slab flaws. Solid colors look sleeker but show every footprint and grain of sand.

Full-broadcast flake floors have a natural texture that grips better than smooth gloss. If you want more traction, we can add a fine anti-slip aggregate to the topcoat. A smooth, partial-broadcast floor is more slippery when wet.

Most garage flake floors take one to two days, depending on the size, the prep and whether the base is epoxy or polyaspartic. Summer humidity can stretch the time between coats. We give you the schedule in writing.

The vinyl chips themselves hold color well. What usually yellows is an epoxy topcoat. We use a UV-stable polyaspartic topcoat so the floor near the door matches the rest of the garage.

For surfaces that see sunlight, usually yes. HomeGuide rates polyaspartic's UV resistance as excellent and epoxy's as poor to fair, and polyaspartic cures much faster. Epoxy still makes a good base coat because it goes on thicker and bonds well, so many floors use both.

HomeGuide lists about $2,000 to $6,900 for a two-car garage and $2,900 to $10,400 for a three-car garage, or $5 to $12 per square foot. We price your floor after measuring and testing it.

HomeGuide says polyaspartic reaches full cure for heavy vehicle traffic in about 24 to 48 hours. Heat and humidity on install day affect that, and we give you a specific time.

It costs a little more than epoxy, it is not a DIY product, and its short working time leaves no room for poor prep. Thin coats also mean a flake build or extra coats are needed for thickness. Good grinding and testing handle most of the risk.

You can, but plain epoxy is a poor fit in full Florida sun. HomeGuide rates its UV resistance as poor to fair, and a smooth gloss gets slick and hot. We use UV-stable, textured systems or acrylic deck coatings outdoors instead.

HomeGuide lists acrylic cool-deck coatings at about $4 to $6 per square foot, epoxy at $4 to $10, and decorative overlays at $6 to $12. Crack repair and removal of old coatings add to that. We price your deck after measuring it.

Light colors and acrylic cool-deck style finishes stay cooler than dark or glossy coatings. HomeGuide describes Kool Deck as a non-slip material that helps lower surface temperature. We bring light color samples so you can compare.

Often, yes. Many condo and HOA communities around Daytona Beach control exterior colors and finishes. Check your rules before booking. We can provide a written system and color description to submit.

This Old House lists metallic epoxy floors at about $5 to $12 per square foot. Design complexity, the number of colors, prep and the size of the room move the price. We give a written price after seeing the floor.

Epoxy can yellow where sunlight hits it. We use a UV-stable topcoat and talk through windows and door exposure before you pick colors, since cool tones show yellowing sooner than warm metallics.

We install metallic floors on concrete only. Tile has grout lines and a glaze that make bonding unreliable, so it needs to come up first. If your slab is under tile, we can quote removal prep.

A smooth metallic finish can be slick when wet. We can add a fine anti-slip additive to the topcoat, and we suggest mats at exterior doors where people come in wet.

HomeAdvisor lists commercial and industrial 100% solids coatings at $12 or more per square foot, and high-grade heavy-use coatings add about 20% to 30%. Simpler floors cost less. We price by area after seeing the space.

Yes. We can work nights and weekends and stage large floors in sections so part of your space stays open. Fast-curing topcoats shorten downtime.

A 100% solids epoxy system with a chemical-resistant topcoat handles common shop fluids well when spills are wiped up. Oil already soaked into the slab must be degreased and ground out first.

Smooth epoxy can be slick when wet. For kitchens and wash areas we add aggregate to create a textured, slip-resistant finish and cove the base so the floor is easy to clean.